Reasons Your fiat multipla key 500 Key Fob Won't Work

A key fob for the Fiat 500 allows you to easily open doors and start your vehicle. There are a myriad of reasons the fob could stop working. This includes a dead battery or water damage, problems with receiver modules, as well as interference.

This listing is for a NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It must be professionally programmed (click here to find local automotive locksmiths). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent reason for your 500 key fob not functioning. Key fobs of today have a limited range of operation and must be within just a few inches of the vehicle to function. If you're not close to your vehicle when you press the key fob button, the car will not respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery on your coin cell (Part number CR2032) by a new one from a trusted brand such as Panasonic, Duracell, or Energizer. You can find them at the local hardware store or online.

After you've replaced the coin cell battery It is possible to test it by standing next to your fiat punto key replacement cost 500 and pressing the buttons. The parking lights should flash and the key fob should operate the lock and unlock switch.

If the key fob won't function after replacing the battery, it could have water damage that prevents it from connecting to the receiver module in your car. Water damage can happen through a variety of methods, including simply splashing or submerging the key fob saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to pull the moisture out. If this doesn't work, your fob may need to be reprogrammed by a professional auto locksmith or by the dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob into the ocean or wash it in a washing machine. Saltwater can cause the circuit board to short and eventually end up dying. The fob getting wet is not an ideal choice, but if you drop it into a glass of water or Fiat Multipla Key do not remember to remove it from your pocket before you run the washer Don't give up hope.

Take the battery off first. Clean the electronic chip with isopropyl or a similar product and then dry it completely before replacing the battery. Check the fob to verify if it's functioning. If the key doesn't function, it may need to be reprogrammed. This is usually done by a professional or dealer auto locksmith.

If the key you have is older and is not programmed for your vehicle it is necessary to replace it completely. This is a simple process which can be accomplished by a professional locksmith for automotive use. The locksmith will need the key cut to match your car's ignition. The locksmith will also need to reprogram your fob into the car's system. This is a fast and affordable process which can be completed in the next day.

Receiver Module Issues

Your 500 key fob may not function because it's out of range. The remote usually has 30 feet of range or less and if it's far away from your car it will not respond to your commands. This can easily be resolved by moving it closer to your vehicle until it starts responding.

If your fob won't work after you replace the battery in the coin, also known as a "button", "watch" or "button" it could be a problem with the internal circuit board. In most cases, reprogramming the fob will solve the issue. You can find the steps for most vehicles on YouTube or in the owner's guide.

It's possible that you need to replace the metal retaining clips that keep the battery of your coin in place. If they lose tension, it can prevent the battery from sitting properly and cause your remote to malfunction.

In rare cases the fob could be disconnected from your vehicle due to software or hardware issues. This can cause a major trouble, but you could frequently fix this issue by visiting a local dealer or auto locksmith to reprogram your fob for fiat Multipla Key you. In certain instances, the software may also require reinstallation into your body control modules.

Interference

In addition to a dead battery on a coin the key fob could not be receiving or transmitting the signal due to interference. This could happen if the key fob is in proximity to an electronic radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob may not function include a weak connection to the buttons and internal chip, or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. It could be a defective 500 receiver module If you've tried replacing it with a battery, reprogramming, or using an alternative key fob. The receiver module, located beneath the dashboard, picks up radio frequency signals from your key fob. It transforms the signals into electronic commands, which are then processed by the vehicle.

Luckily, there is an easy way to reset all of the onboard systems in your 500 keys, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Reconnect the battery. This will erase any remaining electricity, and restart the computer in your car. This could help you get your key fob to function again. If the issue continues, you should consult a certified technician. They will be able to determine the root cause of any problems.